/ ~9 Y6 ?. O0 i, M" d+ P早前有人发过此类应用: " h- n9 k6 f7 {5 ~7 W' N; d0 T" bhttps://www.stmcu.org.cn/module/ ... =page%3D&page=1 * q! m2 E6 A4 N7 r2 N ) D- T. i. D6 P/ l但我建议不要用!:3 {9 d. S& \, ^+ ~# D
ST-LINK也是用的SWD方式,可选4MHz,关键替换后估计不稳定,为什么要替换?! 9 x( k/ U( |* T) }+ l$ A# w9 r1 y) P更重要的是,刷成jlink后一堆限制,建议不要刷了:$ {3 w9 N o# Z- k* f& w
Limitations$ f7 d1 y( h+ W$ [4 k0 ^
The firmware making the ST-LINK on-board J-Link compatible has some limitations in contrast to an original, industry leading SEGGER J-Link: ' L- S* s- ?+ y1 x" K" p; `3 k0 v v) B1.May be used with ARM based ST devices only6 K/ e' D5 K: y" q& `/ p
2.Only debugging on evaluation boards is allowed. Debugging on custom hardware is not supported and not allowed4 W' F# n- o. d' ?9 H+ I
3.No production flash programming support / W* W: N7 P. U2 j* b4 Z4.Unlimited breakpoints in flash available for evaluation only 7 d' v( O {# i. M: J4 T( l5.No support is given , }0 H; T! c7 t# w: {5 a参考: H4 W4 v) |, W/ s# ?8 u http://www.segger.com/jlink-st-link.html
谢楼主分享
可以用你的Nucleo板子做实验,貌似是官方的软件,上次培训的时候从ST的FAE哪儿拷贝过来的....
使用这个工具转换以后,STlink会被识别Jlink,然后可以用Jlink来调试程序了,如果需要再用STlink,就再整一回...
我已经测试过了,好用才放到论坛里的
不喜欢这样的试验~~
呵呵~
早前有人发过此类应用:
https://www.stmcu.org.cn/module/ ... =page%3D&page=1
但我建议不要用!:3 {9 d. S& \, ^+ ~# D
ST-LINK也是用的SWD方式,可选4MHz,关键替换后估计不稳定,为什么要替换?!
更重要的是,刷成jlink后一堆限制,建议不要刷了:$ {3 w9 N o# Z- k* f& w
Limitations$ f7 d1 y( h+ W$ [4 k0 ^
The firmware making the ST-LINK on-board J-Link compatible has some limitations in contrast to an original, industry leading SEGGER J-Link:
1.May be used with ARM based ST devices only6 K/ e' D5 K: y" q& `/ p
2.Only debugging on evaluation boards is allowed. Debugging on custom hardware is not supported and not allowed4 W' F# n- o. d' ?9 H+ I
3.No production flash programming support
4.Unlimited breakpoints in flash available for evaluation only
5.No support is given
参考: H4 W4 v) |, W/ s# ?8 u
http://www.segger.com/jlink-st-link.html
,强烈支持楼主ing……& q4 l5 U, w! P4 Q+ z3 {2 ^; J4 J