" w9 v; j; N7 q6 N9 |早前有人发过此类应用： / m5 w1 W7 W+ G" z2 q% Ghttps://www.stmcu.org.cn/module/ ... =page%3D&page=1 1 U' n8 H: u; A1 z+ H" i ]. {: _: P* G9 `' G; }
但我建议不要用！： O0 H1 C# B4 @1 v- FST-LINK也是用的SWD方式，可选4MHz，关键替换后估计不稳定，为什么要替换？！ ; a* `* U% {! X2 i g/ m; z更重要的是，刷成jlink后一堆限制，建议不要刷了： # {8 k8 e9 ^3 P6 o# Z. bLimitations! r0 ~; b( y- C" X
The firmware making the ST-LINK on-board J-Link compatible has some limitations in contrast to an original, industry leading SEGGER J-Link: $ A( c1 V6 X1 I& \) \4 R$ o1 P1.May be used with ARM based ST devices only 4 n; h h8 u c& Q2.Only debugging on evaluation boards is allowed. Debugging on custom hardware is not supported and not allowed# O* H0 F& Z5 C/ A5 b5 R5 @
3.No production flash programming support6 O; a- k/ Z6 u" b8 \- b
4.Unlimited breakpoints in flash available for evaluation only c8 [7 Z# d7 \3 d& ]0 ^5.No support is given ' f- _, J' }; s* u# G+ S参考： 5 i* u6 o- Y, ?; Bhttp://www.segger.com/jlink-st-link.html
谢楼主分享
可以用你的Nucleo板子做实验,貌似是官方的软件，上次培训的时候从ST的FAE哪儿拷贝过来的....0 ~9 w+ E% Q) j8 {
使用这个工具转换以后，STlink会被识别Jlink，然后可以用Jlink来调试程序了，如果需要再用STlink，就再整一回...
C& }$ D; h0 p$ y: m% E7 z7 s( z
我已经测试过了，好用才放到论坛里的5 }+ @* I) ?1 ~) R, p) p
不喜欢这样的试验~~
呵呵~
早前有人发过此类应用：
https://www.stmcu.org.cn/module/ ... =page%3D&page=1
: _: P* G9 `' G; }
但我建议不要用！：
ST-LINK也是用的SWD方式，可选4MHz，关键替换后估计不稳定，为什么要替换？！
更重要的是，刷成jlink后一堆限制，建议不要刷了：
Limitations! r0 ~; b( y- C" X
The firmware making the ST-LINK on-board J-Link compatible has some limitations in contrast to an original, industry leading SEGGER J-Link:
1.May be used with ARM based ST devices only
2.Only debugging on evaluation boards is allowed. Debugging on custom hardware is not supported and not allowed# O* H0 F& Z5 C/ A5 b5 R5 @
3.No production flash programming support6 O; a- k/ Z6 u" b8 \- b
4.Unlimited breakpoints in flash available for evaluation only
5.No support is given
参考：
http://www.segger.com/jlink-st-link.html
,强烈支持楼主ing……