stm32f030rc 多路ad采样异常

superst 提问时间：2019-1-2 10:56 /

采用hal库，多路采样，发现只要启动ad，ad输入就会莫名其妙有0.4V左右的电压。配置如下，
hadc.Instance = ADC1;
  hadc.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV4 ;
  hadc.Init.Resolution = ADC_RESOLUTION_12B;
  hadc.Init.DataAlign = ADC_DATAALIGN_RIGHT;
  hadc.Init.ScanConvMode = ADC_SCAN_DIRECTION_FORWARD;
  hadc.Init.EOCSelection =ADC_EOC_SEQ_CONV;//
  hadc.Init.LowPowerAutoWait = DISABLE;
  hadc.Init.LowPowerAutoPowerOff = DISABLE;
  hadc.Init.ContinuousConvMode = ENABLE;//
  hadc.Init.DiscontinuousConvMode =DISABLE;
  hadc.Init.ExternalTrigConv =ADC_SOFTWARE_START;
  hadc.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE;
  hadc.Init.DMAContinuousRequests = ENABLE;
  hadc.Init.Overrun =ADC_OVR_DATA_OVERWRITTEN;//

  if (HAL_ADC_Init(&hadc) != HAL_OK)
  {
Error_Handler(ERR_ADC_init);
  }

  __HAL_RCC_DMA1_CLK_ENABLE();

hdma_adc.Instance = DMA1_Channel1;
hdma_adc.Init.Direction = DMA_PERIPH_TO_MEMORY;
hdma_adc.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_adc.Init.MemInc = DMA_MINC_ENABLE;
hdma_adc.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD;
hdma_adc.Init.MemDataAlignment = DMA_MDATAALIGN_HALFWORD;
hdma_adc.Init.Mode = DMA_CIRCULAR;
hdma_adc.Init.Priority = DMA_PRIORITY_MEDIUM;

if (HAL_DMA_Init(&hdma_adc) != HAL_OK)
{
Error_Handler(ERR_DMA_Init);
}

__HAL_DMA1_REMAP(HAL_DMA1_CH1_ADC);

__HAL_LINKDMA(&hadc,DMA_Handle,hdma_adc);

  if (HAL_ADCEx_Calibration_Start(&hadc) != HAL_OK)
  {

Error_Handler(ERR_ADCEx_Cal);
  }

sConfig.Channel = ADC_CHANNEL_0;
  sConfig.Rank =ADC_RANK_CHANNEL_NUMBER;
  sConfig.SamplingTime = ADC_SAMPLETIME_13CYCLES_5;
  if (HAL_ADC_ConfigChannel(&hadc, &sConfig) != HAL_OK)
  {
Error_Handler(ERR_ADC_Config);
  }

sConfig.Channel = ADC_CHANNEL_6;

  if (HAL_ADC_ConfigChannel(&hadc, &sConfig) != HAL_OK)
  {
Error_Handler(ERR_ADC_Config);
  }

  sConfig.Channel = ADC_CHANNEL_7;
  if (HAL_ADC_ConfigChannel(&hadc, &sConfig) != HAL_OK)
  {
Error_Handler(ERR_ADC_Config);
  }

  sConfig.Channel = ADC_CHANNEL_14;
  if (HAL_ADC_ConfigChannel(&hadc, &sConfig) != HAL_OK)
  {
Error_Handler(ERR_ADC_Config);
  }
sConfig.Channel = ADC_CHANNEL_15;
  if (HAL_ADC_ConfigChannel(&hadc, &sConfig) != HAL_OK)
  {
Error_Handler(ERR_ADC_Config);
  }
硬件io配置如下
__HAL_RCC_ADC1_CLK_ENABLE();

__HAL_RCC_GPIOA_CLK_ENABLE();
__HAL_RCC_GPIOC_CLK_ENABLE();

/**ADC GPIO Configuration
PA0    ------> ADC_IN0
PA6    ------> ADC_IN6
PA7    ------> ADC_IN7
PC4    ------> ADC_IN14
PC5    ------> ADC_IN15
*/
GPIO_InitStruct.Pin =AD6_NOISE_Pin| AD0_V25_Pin|AD7_R_Pin；
GPIO_InitStruct.Mode =GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed=GPIO_SPEED_FREQ_HIGH;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

/* GPIO_InitStruct.Pin = AD14_R_Pin|AD15_R_Pin;
GPIO_InitStruct.Mode =GPIO_MODE_ANALOG;
GPIO_InitStruct.Pull =GPIO_NOPULL;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);*/

之后在while（1）前启动ad，调用如下
HAL_ADC_Start_DMA(&hadc, (uint32_t *)ADCConvertedDMABUF, 5）；
之后测量各路的ad输入，正常应该是0V，可测量得到是0.4V左右，ad值为600左右。