STM32F030 串口中断问题

wanyisq 提问时间：2017-12-27 18:05 /

我用的是STM32F030K6
串口初始化程序如下：
      GPIO_InitTypeDef GPIO_InitStructure;
USART_InitTypeDef USART_InitStructure;

      RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 , ENABLE );

/*********ÅäÖÃUART1********************/
GPIO_PinAFConfig(GPIOB,  GPIO_PinSource6, GPIO_AF_0); //PB6 PB7?????UART1
GPIO_PinAFConfig(GPIOB,  GPIO_PinSource7, GPIO_AF_0); //?????????(?????)

GPIO_PinAFConfig(GPIOB,  GPIO_PinSource6, GPIO_AF_0);
GPIO_PinAFConfig(GPIOB,  GPIO_PinSource7, GPIO_AF_0);

/* Configure USART Tx as alternate function push-pull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_Init(GPIOB, &GPIO_InitStructure);
/* Configure USART Rx as alternate function push-pull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7;
GPIO_Init(GPIOB,&GPIO_InitStructure);



USART_InitStructure.USART_BaudRate = 9600;
USART_InitStructure.USART_WordLength =  USART_WordLength_8b;
USART_InitStructure.USART_StopBits =  USART_StopBits_1 ;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode =  USART_Mode_Tx | USART_Mode_Rx ;
USART_Init(USART1, &USART_InitStructure);

// USART_ITConfig(USART1, USART_IT_TC, ENABLE);
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
USART_Cmd(USART1, ENABLE);

      NVIC_InitTypeDef NVIC_InitStructconfig;

NVIC_InitStructconfig.NVIC_IRQChannel = USART1_IRQn;
NVIC_InitStructconfig.NVIC_IRQChannelPriority = 1;
NVIC_InitStructconfig.NVIC_IRQChannelCmd = ENABLE;

NVIC_Init(&NVIC_InitStructconfig);

串口中断函数如下：

void USART1_IRQHandler(void)
{
  if(USART_GetITStatus(USART1, USART_IT_RXNE) != RESET)
  {
UsartType.RX_pData[UsartType.RX_Size++]=(USART1->RDR & (uint16_t)0x01FF);
USART_SendData(USART1,USART1->RDR);
if(UsartType.RX_Size>=200)
{
UsartType.RX_Size=0;
}

            USART_ClearFlag(USART1,USART_IT_RXNE);

  }

}

函数功能就是串口把接收到的数据再发出来。
目前的现象是在中断函数设置一个断点，进入断点后再全速运行，就接收不到数据了，无法进入中断。
哪位大神知道问题在哪